Skip to content Skip to sidebar Skip to footer

Cara Mengatasi Error E017-003 Canon iR Advance 6055

Salam jumpa lagi soba fotocopy dimanapun anda berada pada kesempatan yang baik ini saya akan membagikan sedikit informasi tentang cara mengatasi dari terjadinya Error E017-003 yang terjadi pada mesin fotocopy Canon imageRUNNER Advance 6055 yang mana mesin mengalami kegagalan dalam bekerja.

Beberapa langkah untuk memperbaiki dari keluarnya Error E000017-003 pada mesin fotocopy Canon imageRUNNER Advance 6055 langkah ini cukup mudah, Letak masalah ini terjadi pada sensor ETB jika anda mencarinya dimana letaknya sensor ini pas tepat berada dibagian bawah ETB atau karet berwarna hitam yang berfungsi sebagi pengganti wayer bawah.
Cara memeperbaikinya juga terbilang cukup mudah hanya dengan membersihkannya saja dengan cara di kuas - kuas dengan menggunakan kuas yang lembut atu menggunakan kuas yang halus sampai bersih biasanya mesin akan kembali normal.

Dibawah ini adalah beberapa kode Error yang berkaitan dengan terjadinya Error 0017 yang terjadi pada mesin fotocopy Canon imageRUNNER Advance 6055 silahkan anda pahami supaya tidak terjadi kesalahan pada saat melakukan perbaikan.

Code: Error E017-0001
Description:
ETB release error
The ETB release was not completed within the specified time period.

Fix:
1.      Recheck the ETB Disengage connection on the Sensor (PS56). Sensor side: J2101, J3270 and PCB side: J343 (Duplex Driver PCB (PCB4))
2.      Recheck the connection between the Duplex Feed Left Motor (M19). Motor side: J2107, J3044 (relay), on PCB side: J330 (and Duplex Driver PCB (PCB4))
3.      Replace the ETB Disengage Sensor unit (PS56).
4.      Replace the Duplex Feed Left Motor (M19).
5.      Replace the Duplex Driver PCB (PCB4).
6.      Replace the DC Controller PCB (PCB1). NOTE: Check that Cam Disengagement is stained. If necessary, clean it. Check whether the drive system (gear, motor, one-way) failed. If necessary, just replace it. Check if there is a link with the Fixing Feed Handle that failed. If necessary, just replace it.

Code: Error E017-0002
Description:
ETB involvement error
ETB involvement is not completed within the specified time period.

Fix:
1.      Recheck the connection between the ETB Disengage Sensor (PS55). Side to Sensor: J2100, J3270, PCB Side: J343 (PCB Driver Duplex Unit (PCB4))
2.      Recheck the connection between the Duplex Feed Left Motor (M19). Motor side: J2107, J3044 (relay), also PCB side: J330 (Duplex Driver PCB (PCB4))
3.      Replace the ETB Engage Sensor (PS55).
4.      Replace the Duplex Feed Left Motor (M19).
5.      Replace the Duplex Driver PCB (PCB4).
6.      Replace the DC Controller PCB (PCB1). NOTE: Check that Cam Disengagement is stained. If necessary, clean it. Check whether the drive system (gear, motor, one-way) failed. If necessary, just replace it. Check again if there is a link with the Fixing Feed Handle that failed. If necessary, just replace it.

Code: Error E017-0003
Description:
HP ETB error
ETB involvement that is not completed at initialization.

Fix:
If any of these errors occur during installation, these Transfer Frame Stopper ETB Members can be left or not deleted. Look for the "Recovery that will be applied when the Release Member on ETB (Transfer Frame Stopper) problem is left undeleted" in the Service Manual, and check whether there are ETB Release Members that are left undeleted or not and also apply the appropriate procedures. If this error occurs at a time other than installation, follow the steps below to apply the check and make improvements.

1.      Recheck the ETB Disengage Sensor (PS56) connection. Sensor side: J2101, J3270, on PCB side: J343 (Duplex Driver PCB (PCB4))
2.      Re-check the Duplex Feed Left Motor (M19) connection. Motor side: J2107, J3044 (relay), on PCB side: J330 (Duplex Driver PCB (PCB4))
3.      Replace the ETB Disengage Sensor number (PS56).
4.      Replace the Duplex Feed Left Motor unit (M19).
5.      Replace the Duplex Driver PCB (PCB4).
6.      Replace the DC Controller PCB (PCB1). NOTE: Check that Cam Disengagement is stained. If necessary, clean it. Check whether the drive system (gear, motor, one-way) failed. If necessary, please replace it. Check whether the link with the Fixing Feed Handle unit failed. If necessary, just replace it.

Demikianlah sedikit informasi tentang cara mengatasi dari terjadinya Error E0017-003 yang terjadi pada mesin fotocopy Canon imageRUNNER Advace 6075 dan semoga artikel ini bisa menambah wawasan dari berbagimacam kendalayang terjadi atau trouble yang sedang terjadi pada mesin anda.

Post a Comment for "Cara Mengatasi Error E017-003 Canon iR Advance 6055"